SlingFin Cinder Cone 4P Pyramid Tent Package

The complete pyramid setup, poles and bug protection included

The SlingFin Cinder Cone 4P Pyramid Tent Package brings together the Cinder Cone 4P Pyramid Tent, the Cinder Cone 4P Mesh Body and the Cinder Cone Carbon Pole, so the shelter arrives ready to pitch anywhere without borrowing ski poles, trekking poles or a paddle. Used together the three pieces make a fully enclosed four person tent with a bathtub floor and no-see-um mesh, palatial floor space and enough height to stand up and change, at a packed weight that undercuts most three person tents. Radial Seam Tape, a reinforcement technique borrowed from the parachute industry, runs inside all four corner seams to hold the silnylon canopy evenly tensioned as the fabric elongates in wet weather, while dual upper thru vents, a large low vent and Perimeter Pull Vents create a chimney effect that helps minimise condensation. The mesh body stays attached to the outer for a fast, dry pitch, and each piece also works on its own, so the shelter can run floorless for ski touring and alpine objectives, then convert to a bug proof tent when the season turns.

Features

• Complete three piece system: Cinder Cone 4P Pyramid Tent, Cinder Cone 4P Mesh Body and Cinder Cone Carbon Pole
• Pitches without ski poles, trekking poles or a paddle thanks to the included adjustable length carbon centre pole
• Converts from a floorless four person shelter to a fully enclosed bug proof tent with a full bathtub floor
• Mesh body stays attached to the outer shelter for a fast, dry pitch, and can also be pitched on its own
• Radial Seam Tape inside all four corner seams eliminates bias stretch and maintains structural integrity in wet conditions
• Two upper drawstring thru vents plus one large low drawstring vent and window for more airflow than peak vents alone
• Perimeter Pull Vents lift the bottom edges in the centre to draw air under the perimeter
• Three drawstring openings in the mesh body give access to the Cinder Cone vents
• Dyneema Quick-Pitch cord sets correct corner spacing for a square pitch, then unclips once the shelter is in use
• YKK VISLON Aquaguard zipper on the shelter sheds rain without a zipper flap, with two preinstalled spare sliders
• YKK VISLON T-shaped door on the mesh body handles grit and sand far better than a coil zipper, and ties back to hold open
• ALUULA Durlyte top cap reinforcements on both shelter and mesh body carry the load from poles or a paddle
• Seven guy out loops, four at the corners and three mid panel, plus four perimeter pull out loop tensioners
• Straight cut sides can be sealed against the ground, with a herringbone bottom perimeter for abrasion resistance
• Internal o-rings in both the shelter and the mesh body for hanging gear or a clothesline
• Includes seven reflective Dyneema core guylines with pre-attached tensioners
• Includes eight size L and seven size MS DAC J-stakes
• Adjustable pole range allows the pitch height to be tuned to the ground and conditions

Specifications

• Claimed Weight (package, minimum): 1.81 kg
• Claimed Weight (package, packaged): 2.17 kg
• Claimed Weight, Pyramid Tent (minimum): 765 g
• Claimed Weight, Mesh Body (minimum): 737 g
• Claimed Weight, Carbon Pole: 306 g
• Shelter Floor Dimensions: 274.0 (W) x 274.0 (D) cm
• Shelter Total Area: 7.53 sq m
• Shelter Peak Height: 183.0 cm
• Mesh Body Floor Dimensions: 269.0 (W) x 269.0 (D) cm
• Mesh Body Floor Area: 7.25 sq m
• Mesh Body Interior Height: 183.0 cm
• Packed Size, Pyramid Tent (uncompressed): 30.5 (L) x 13.0 (W) x 13.0 (H) cm
• Packed Size, Mesh Body (uncompressed): 30.0 (L) x 13.0 (W) x 13.0 (H) cm
• Carbon Pole Length: 177.8 cm to 193.0 cm, adjustable
• Carbon Pole Packed Length: 35.6 cm
• Carbon Pole Diameter: 2.1 cm
• Guylines: 7 x 305.0 cm, 1.5 mm Dyneema core reflective
• Canopy Material: 10D Nylon 66 ripstop, silicone coated both sides
• Mesh Material: 15D Nylon no-see-um mesh
• Floor Material: 20D Nylon ripstop, PE coated, 1800 mm
• Pole Material: 3K twill carbon fibre
• Reinforcement Material: ALUULA Durlyte HH-155 top cap, 20D PE coated reinforcements